Видео

Ja pierdole wow dziękuję ❤❤❤

Nice video hands down

You forgot to include putting back the tensioner pulley… Great vid

Great video very informative and easy to understand… I’m about to tackle this job on my 2012 Dodge Charger! Thank you!

Jesus christ disassemble the truck fuck what's the cost for that job approx.

That's an amazing repair. I have a question, though. Since you were able to remove the front cap (29:46) to get the cam shaft up high enough to replace the front rods and rockers , couldn't all of the rods and rockers (for that cam shaft) have been replaced at that point? I have a 2015 that's beginning to tick, so, I expect to be doing this repair.

U r a f-kin genius

Thank you.. While it did not show everything, it pointed me in the right direction. The AC lines on the passenger side, and a large wiring harness on the drivers side make getting the rad out difficult. But a few zips ties cut and some careful pushing of the AC lines and the rad came out. Everything else is spot on... Ty again.

Nice video on explaining everything boss. Question does this apply similar to a non afm 5.3

Was that high beam or low beam?

I Always clean the radiator 'cause have particles. Thanks buddy.

A2Z Auto Masters. Great video, you are very detailed. My one question is the torque numbers you listed are much different than the honda instructions for a 2018 Accord 1.5 t. Am I reading something wrong?

A couple years ago I carefully watched this video and successfully made the repairs on the driver side. Now it's time for the passenger side... Wish me luck! Thanks for the video!!

Great job. Thank you for sharing

Great job on your video

My 2018 honda accord with 105,000 miles and it already has a blown head hasket

This needs to be a recall..

hope your spec is correct for head torque. Our IN network is down LOL! so im trusting you

<--- 2018 Honda Accord Hybrid 2.0L (single owner), 68,536 miles, head gasket needed to be replaced as per Honda. $4,591.41 repair!!! Corporate would not do a courtesy repair nor contribute towards the repair due to maintenance performed at other than Honda dealerships. I will NEVER buy a Honda again!

Thanks..Work like charm.Like button smashed!

Anybody have a list of tools needed before starting

Have you ever heard of the cylinder deactivation solenoid having a leak on the Chevy 5.3 engine, causing low oil pressure issues?

so how many qts of power steering fluid did you need to refill the system when you were done? and was all of that grease on the steering rack boots from the bad rack? I plan I changing the rear motor mount while I'm in there, Do you have good access to it from under there. new cv axles lower control arms and I think they are called drag link bars, iv already done new trans mounts and struts well be done soon. when you put the rack back up in there-the first two bolts that you put back in were the two that hold it to the frame-at 11;34 in the video I can see a bolt to the right of your two bolts and right above the driveshaft-I watched another video and he took that bolt out that looks like it goes through a round support of some kind, I see that you did not take that out. Would that be the bottom bolt for the rear motor mount? Did you clock the new power steering rack before you put it back up in there-you know turn it all the way to the left and then all the way to the right-then find the middle? what kind of symptoms were you having that made you do this job? I am sorry for all of the questions but on going to do this in my driveway on my back with no help, I did not see too many good places to support the car with the sub-frame, not an option.

Thank you!

Thanks dude, tried all the technical stuff and it wasn’t working. Batteries out did the trick! Legend.

Great video

Please don't use magnets near the magnetic cam position wheel good way to end up needing new camshafts.

Any ideas of how you time new cam and cam phasers using too dead center #1 piston method without taking off timing chain cover

Is this the same engine it made by Dodge??

Great video. What is the torque for the fill plug? Workshop manual has a weird ratio with a special tool.

Did you replace the rivets on the new gasket?

You didn’t have any issues using the torque sequence for the 2.0 head bolts and not the 1.5?

Just wanna take the time to say thank and I got too much love for you and your videos‼️💪😎💯💯👏😇

This is why I didn’t buy the Honda accord 1.5t cuz of this issue and the cvt trans. Brought a 2018 Toyota Camry a lot more reliable and a lot better looking car.

What type of bolt did you use to take the pump out

Great video. But the bloody music.

Excellent job and video

wonderful and very use full video buddy keep it up. i love to hear the sound of the enigine with one single crank that shown you know how to time the engine on spot.

Need advice on how to fixed unlock n lock system for all my doors thanks 08 impala

Mine was starting to tick at 50k. Always used Mobil one. Changed leaking oil cooler. Ran the same Mobil one filter. Poured in 6 quarts of pennezoil platinum 5w20. 10k miles of quite operation.

Hi, I have n26, but after timing chain replace engine sound like diesel… maybe you know what’s the problem ? 😢

I think you're better off to do an AFM delete immediately before a lifter fails & damages the cam..

Thank you. How often should the engine filter be changed?

what about for the 3.8?

What size were the bolts that you used to step the water pump out?

Excellent Video. I really appreciate you taking the time to show the whole process with such details. Kudos to you. 👏 On another note, I can't believe no one has bother to post the proper part number for the head bolts. 🤦🏻‍♂️

Excellent. Thanks for sharing.

Great!! Great! Video . One question? Did you have the head resurface also? My and son and I are in the process of doing this now and because of your video we are saving him ^$6G. Thanks again!!

How can someone link you directly. I really watch and appreciate your explanations. I learn a lot of it

YOU SAVED ME, BRO.... THIS JEEP IS A PUZZLE. not a mechanic but I know my way around a car. The first car I have ever seen this setup. BUT the best video is well-explained step by step. Thank you.